Laying the infrared film floor

Autumn weather takes many by surprise. So, the change in temperature in the street directly affects the microclimate in the room, this is especially noticeable during the off-season, when central heating is not yet connected. Everyone is trying to solve this issue as quickly and inexpensively as possible. The most rational option, where there is a combination of reasonable prices and good heat dissipation are electric underfloor heating. But if necessary, a quick solution to the problem is to give preference to film infrared floors, which are mounted directly under the laminate or linoleum and do not require a cement-sand screed. The cable floor is laid directly under the tile, and full system commissioning is possible not earlier than in 14-18 days, until the tile adhesive is completely dry.

Laying the infrared film floor with your own hands

Installing the film floor linoleum flooring,laminate and carpet is as fast as possible and allows you to put the system into operation immediately after the completion of laying the flooring and looks like this: 1) The subfloor must be relatively flat, clean, and dry. The substrate is spread over the entire area of ​​the room, and not just under a warm floor, in order to avoid drops. It is advisable to give preference to high-quality thermal insulation, designed specifically for the "warm floor" systems. It should have a protective coating and withstand a high temperature range, since when the system is put into operation for the first time at the beginning of the season, manufacturers recommend setting the temperature on the thermostat close to the maximum. Accordingly, the infrared film is heated to about 47-50 degrees. A poor-quality substrate will simply not withstand such floor heating, will melt and become unusable.
Laying the infrared film floor
Laying the infrared film floor
Laying infrared film floor
Laying the infrared film floor
Laying the infrared film floor
Laying the infrared film floor
Laying the infrared film floor
Laying infrared film floor
2) A place for the thermostat is prepared in advance, which is mounted in an area not exposed to drafts and a place protected from direct sunlight, otherwise their determination of the temperature will not be correct. The height of the installation is determined according to the recommendations of the manufacturers from 30 and up to 120 cm. For the floor sensor, the canvas is shaved, the corrugation is inserted into it, into which the floor sensor is inserted. The length of the sensor depends on the distance of the heating film. He should go under it strictly in the middle of one of the segments. Under the thermoregulator a special dose box is used, it differs in depth and large diameter.This is explained by the presence of a large number of connecting wires, which will not stand up as needed in a standard box.
Laying the infrared film floor
Laying the infrared film floor
Laying the infrared film floor
Laying infrared film floor
2) Floors are mounted on a space that is not occupied by furniture. Installation of a heated floor under furniture is allowed, provided that it has legs at least 10 cm. The strips are connected to each other with a strong copper cable, the thickness of which depends on the total power of the system. The cable is connected using special connecting terminals (included in the package to the film floor), which are then carefully insulated with a bitumen insulator.
Laying the infrared film floor
Laying the infrared film floor
Laying infraredfilm floor
3) The installation of the thermostat takes place simultaneously with the infrared heat-insulated floor according to the attached wiring diagram. As a rule, all thermostats, regardless of the manufacturer, are connected to the power source and the heat-insulated floor using the same scheme. 4 ) At the final stage, they test the system and check the degree of heating of all stripes of a heated floor. This takes at least 5-10 minutes. The layout is drawn. 5) To protect against moisture, many film floor manufacturers recommend covering it with polyethylene on top A new medium density film.
Laying infrared film floor
 Laying infrared film floor
Laying infrared film floor
 Laying infrared film floor After laying the flooring, which serves as linoleum, laminate or carpet, you can immediately put the floor heating system into operation. But it is worth considering that in order to fully warm the room to a warm floor, depending on the temperature conditions outside and inside the room,substrate quality and quadrature of the infrared floor may take from several hours to a day.

Date: 18.10.2018, 04:52 / Views: 33584

Related News


Eggplant parmesan in italian
Rights: dream, dream
Crispy and flavorful cheese balls. Why did I not cook this yummy before?
How to unprotect .pdf
Knitted split swimsuit in shades of green